tukilluki napísal:aky je rozhranie ktore ma skenovat? to je jak iwlist WLAN0 scan tak podobne hcitool scan hci0 napriklad (hciconfig vypise rozhrania)
Hciconfig mozno vypise rozhrania, ano to mas pravdu, ale nie u mna. To hci0 som tam dal len na ukazku, ziadne take zariadenie sa v /dev nenachadza a ani nikdy nevytvori. Ale dakujem, problem je vyrieseny. Vysvetlenie je zaujimave a hodne iritujuce. Aj ked ano, laptop je predavany s vistou, tak jediny, kto ma problem som opat len ja. Bluetooth adaptery dell truemobile 350, 355, 360 obsahuju firmware upraveny pre Vistu. / mozno aj ine, tieto urcite / Riesenie je len jedno a to skutocne. Treba spustit vistu / alternativne staci aj XP plus aplikacia zo stranok Dell / na zapnutie bluetooth. Potom restart, nabootovanie debianu a vsetko funguje out-of-box. Prosim, tu su aj dake vypisy, co som porobil pred restartom:
Kód: Vybrať všetko
lsusb -v -d 0a5c:4500
Bus 005 Device 005: ID 0a5c:4500 Broadcom Corp.
Device Descriptor:
bLength 18
bDescriptorType 1
bcdUSB 2.00
bDeviceClass 9 Hub
bDeviceSubClass 0 Unused
bDeviceProtocol 0 Full speed (or root) hub
bMaxPacketSize0 8
idVendor 0x0a5c Broadcom Corp.
idProduct 0x4500
bcdDevice 1.00
iManufacturer 1 Broadcom
iProduct 2 BCM2045B2
iSerial 0
bNumConfigurations 1
Configuration Descriptor:
bLength 9
bDescriptorType 2
wTotalLength 25
bNumInterfaces 1
bConfigurationValue 1
iConfiguration 0
bmAttributes 0xe0
Self Powered
Remote Wakeup
MaxPower 0mA
Interface Descriptor:
bLength 9
bDescriptorType 4
bInterfaceNumber 0
bAlternateSetting 0
bNumEndpoints 1
bInterfaceClass 9 Hub
bInterfaceSubClass 0 Unused
bInterfaceProtocol 0 Full speed (or root) hub
iInterface 0
Endpoint Descriptor:
bLength 7
bDescriptorType 5
bEndpointAddress 0x81 EP 1 IN
bmAttributes 3
Transfer Type Interrupt
Synch Type None
Usage Type Data
wMaxPacketSize 0x0001 1x 1 bytes
bInterval 255
Hub Descriptor:
bLength 9
bDescriptorType 41
nNbrPorts 3
wHubCharacteristic 0x0004
Ganged power switching
Compound device
Ganged overcurrent protection
bPwrOn2PwrGood 50 * 2 milli seconds
bHubContrCurrent 100 milli Ampere
DeviceRemovable 0x0e
PortPwrCtrlMask 0xff
Hub Port Status:
Port 1: 0000.0100 power
Port 2: 0000.0103 power enable connect
Port 3: 0000.0103 power enable connect
Device Status: 0x0000
(Bus Powered)
Kód: Vybrať všetko
dellWirelessCtl --info
Libsmbios version : 2.0.3
dellWirelessCtl version: 0.3.0
Wireless Info:
Hardware switch supported
Hardware switch is On
WiFi Locator supported
Wireless Keyboard not supported
NVRAM Size: 256 bytes
NVRAM format version: 1
Radio Status for WLAN:
WLAN supported
WLAN installed
WLAN enabled
Status Code: 0
Radio Status for Bluetooth:
Bluetooth supported
Bluetooth installed
Bluetooth enabled
Status Code: 0
Radio Status for WWAN:
WWAN supported
WWAN not installed
WWAN enabled
Status Code: 2
Wireless Switch Configuration
WLAN switch control on
Bluetooth switch control on
WWAN switch control on
switch config not locked
WiFi locator enabled
WiFi Locator config not locked
BIOS Boot-time settings (new interface):
Wireless_Switch_Cellular_Control_Enable: 1
Wireless_Switch_Cellular_Control_Disable: 0
Wireless_Switch_Bluetooth_Control_Enable: 1
Wireless_Switch_Bluetooth_Control_Disable: 0
Wireless_Switch_Wireless_LAN_Control_Enable: 1
Wireless_Switch_Wireless_LAN_Control_Disable: 0
WiFi_Locator_Enable: 1
WiFi_Locator_Disable: 0
Cellular_Radio_Enable: 1
Cellular_Radio_Disable: 0
Bluetooth_Devices_Enable: 1
Bluetooth_Devices_Disable: 0
Wireless_LAN_Enable: 1
Wireless_LAN_Disable: 0
BIOS Boot-time settings (old interface):
Radio_Transmission_Enable: (NOT SUPPORTED)
Radio_Transmission_Disable: (NOT SUPPORTED)
Wireless_Device_Disable: (NOT SUPPORTED)
Wireless_Device_App_Control: (NOT SUPPORTED)
Wireless_Device_App_Or_Hotkey_Control: (NOT SUPPORTED)
A momentalna situacia, som spustil hcitool -scan a aj to tvoje hciconfig -a a ako mozes vidiet, je to tam
Kód: Vybrať všetko
pato@debian:~$ hcitool scan
Scanning ...
00:18:13:14:F1:BE W810i
pato@debian:~$ hciconfig -a
hci0: Type: USB
BD Address: 00:22:69:BF:DA:06 ACL MTU: 1017:8 SCO MTU: 64:8
UP RUNNING PSCAN ISCAN
RX bytes:2913 acl:18 sco:0 events:109 errors:0
TX bytes:912 acl:21 sco:0 commands:46 errors:0
Features: 0xff 0xff 0x8f 0xfe 0x9b 0xf9 0x00 0x80
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH HOLD SNIFF PARK
Link mode: SLAVE ACCEPT
Name: 'debian-0'
Class: 0x000100
Service Classes: Unspecified
Device Class: Computer, Uncategorized
HCI Ver: 2.0 (0x3) HCI Rev: 0x216f LMP Ver: 2.0 (0x3) LMP Subver: 0x41d8
Manufacturer: Broadcom Corporation (15)
Doteraz by som dal ruku do ohna, ze jeden os nemoze ovplyvnit druhy /aj ked toto je troska ina situacia, lebo zrejme posle do toho zariadenia daku hodnotu, co ho vypne a ta hodnota tam ostava az do dalsej zmeny / Je to ale ubohost proste, tak zo strany dellu, broadcom a aj z MS.
p.s.: Update
To co som opisoval vyssie samozrejme plati, no treba to nastastie urobit len prvy krat. Neskor sa bluetooth da vypinat aj zapinat pomocou tohto prikazu:
Kód: Vybrať všetko
dellWirelessCtl --sw_bt 1 --bt 1 # pre zapnutie
dellWirelessCtl --sw_bt 1 --bt 0 # pre vypnutie
