zdarte mam MB MS - 7021 a zvukovka je na nej integrovana a potrebujem vnutri bedne zapojit nejaky konektor aby som ho mohol viviest jack na predok case. mal som od kamarat pazicany ten kablik co ide do CD-ROM mal 3 zily a 4 piny a strkal sa do portu na zvukovke len ziadny zvuk nesiel .
Ď za radu

a nemam od nej manual! notak to fakt nikto nevie?

Od toho jacku ti musia ist nejake kable, ktore nebudu nikde zapojene. No a tie kable musis zapojit na maticnu dosku. Kazda maticna je ina, takze skus najst manual od dosky na nete.

Konkrétnejšie označenie dosky nevieš poskytnúť? Prípadne napíš parametre.

ved je to od Microstar MS - 7021

CPU

• Supports Socket A for AMD® Athlon™/Athlon™ XP/Duron™ processors @FSB 200/266/333/400 MHz
• Supports to Athlon™ XP 3200+ processor or higher

Chipset

• VIA® KT600 Chipset
- Supports FSB @200/266/333/400MHz
- Supports dual channel native SATA controller up to 150MB/s with Raid 0 or Raid 1
- Integrated Hardware Sound Blaster/Direct Sound AC97 audio
- Ultra DMA 66/100/133 master mode PCI EIDE controller
- ACPI & PC2001 compliant enhanced power management
- Supports USB2.0 up to 8 ports

• VIA® VT8237 Chipset
- Integrated Hi-Speed USB 2.0 controller, 480Mb/sec, 8 ports
- 2 Serial ATA/ 150 ports
- 2 channel Ultra ATA 100 bus Master IDE controller
- PCI Master v 2.3, I/O APIC
- Supports both ACPI and legacy APM power management - Serial ATA/150 RAID 0

Main Memory

•
Supports four memory banks using two 184-pin DDR DIMMs
• Supports a maximum memory size up to 2GB
• Supports 2.5v DDR SDRAM DIMM
• Supports DDR400/333/266/200 SDRAM

Slots

• One AGP (Accelerated Graphics Port) slot
- AGP specification compliant
- Support AGP 3.0
Five 32-bit Master PCI Bus slots
• Supports 3.3V/5V PCI bus Interface

BIOS

• The mainboard BIOS provides "Plug & Play" BIOS which detects the peripheral devices and expansion cards of the board automatically.
• The mainboard provides a Desktop Management Interface (DMI) function which records your mainboard specifications.

On-Board IDE

• An IDE controller on the VT8237 chipset provides IDE HDD/CD-ROM with PIO, Bus Master and Ultra DMA 66/100/133 operation modes. It can connect 4 Ultra ATA drives.
• Serial ATA/150 controller integrated in VT8237
- Up to 150MB/s transfer speed
- Can connect up to 2 Serial ATA drives
- Support RAID 0, RAID 1

USB Interface

8 USB ports
- Controlled by VT8237 southbridge
- 4 ports in the rear I/O, 4 ports via the external bracket

Audio

AC'97 link controller integrated in VIA 8237
5.1 channel audio supported by Realtek ALC655 codec
- Compliance with AC'97 v2.2 spec.
- Meet PC2001 audio performance requirement

On-Board Peripherals

- 1 floppy port supports 1 FDD with 360K, 720K, 1.2M, 1.44M and 2.88Mbytes
- 1 serial ports (COM A )
- 1 parallel port supports SPP/EPP/ECP mode
- Line-In/Line-Out/Mic-In port
- 1 RCA SPDIF Out
- 1 RJ-45 jack
- 1 D-Bracket2 pinheader

na stranke vyrobcu

http://www.msi.com.tw/program/support/m ... 511&kind=1

takze som to nasiel pod grafou a napojil tam kable tie piny 5,6 a 9,10 boly spojene tym obdlznikom ako je na CD mechanike alebo na HDD ked ich odpojim nejde mi zvuk vzadu na jacku, asi preto tam je to front panel a from front panel, aby siel zvuk bud vzadu alebo vpredu.
Kedze takych "obdlznikov" mam hojnu zasobu tak som napojil kable tak ako su na obrazku na JACK no len na samicu nie na samca a mam ten problem ze to strasne susti ked nejde zvuk.
Ked dam zvuk nahlas tak sustanie nie je pocut ale ked mam pusteny napr iba hlas tak mi to tam dost vadi. Je mozne ze som to zle zapojil?Ď

clarrick napísal:takze som to nasiel pod grafou a napojil tam kable tie piny 5,6 a 9,10 boly spojene tym obdlznikom ako je na CD mechanike alebo na HDD ked ich odpojim nejde mi zvuk vzadu na jacku, asi preto tam je to front panel a from front panel, aby siel zvuk bud vzadu alebo vpredu.
Kedze takych "obdlznikov" mam hojnu zasobu tak som napojil kable tak ako su na obrazku na JACK no len na samicu nie na samca a mam ten problem ze to strasne susti ked nejde zvuk.
Ked dam zvuk nahlas tak sustanie nie je pocut ale ked mam pusteny napr iba hlas tak mi to tam dost vadi. Je mozne ze som to zle zapojil?Ď

z tvojho nakresu som nezistil,ako to mas presne na jacku zapojene,ale v kazdom pripade ma na jacku okrem laveho a praveho kanala byt zem (2 na jumpere) (ground) a nie DC 5V